I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?
We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.

Another saw that earns good marks from both professionals and users is the DeWalt DWE7491RS (Est. $500). Todd Fratzel of ToolBoxBuzz.com, who says he's normally a "huge fan" of Bosch table saws, nonetheless declares this DeWalt "the best overall job site + mobile stand option out there." He praises the power and accuracy of the table saw, adding that it had no trouble dealing with various materials he tested (3/4-inch plywood, 2x framing material, and 1x maple lumber). He also notes that its rip capacity of 32-1/2 inches is bigger than any other portable saw's – a full 7-1/2 inches bigger than the Bosch 4100-09's. Fratzel loves the wheeled mobile stand, which makes it easy for one person to move this fairly heavy saw (roughly 90 pounds). He says the stand is very easy to set up and allows for the saw to be stored on end, taking up less space.
These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.
When you purchase your table saw, more than likely it will have standard 10” carbide tipped blade that is good for general purpose use. This blade is capable of cross cutting a 4 x 4. If you replace it with a 40 tooth combination blade you will improve the quality of your cuts significantly and more than likely be much happier with the blade overall. You can get specialty blades also if you are going to be cutting other materials as well.
You often find that many contractors have a love hate relationship with blade guards. Many contractors and woodworkers simply find they often get in the way and can often get wood stuck in them. But many manufacturers are improving these guard’s year on year and now many of them are very advanced and will help keep your fingers from getting hurt, we always advise you to consider the table saw blade feature on any table saw in detail as it could one day help saw you.
Both the riving knife and the blade itself has a quick release design that lets you remove each one in minutes after accessing the arbor lock and without using any special tools either. The blade guard has a similar design that allows you to remove and replace it without any tools. This guard does a good job of keeping your hands and any other body parts safe as you use the saw.
You’ll be able to keep your space clear and work better with fewer distractions. The DEWALT DWE7490x 10 Inch Table Saw also comes with a push stick included in the kit so you’ll be able to take protective measures when you work. We’d recommend the DEWALT DWE749x to anyone as a good addition to their go to tools. It is an excellent tool and will help you do some of the best work of your life.

Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
You will need specialty blades for cutting materials such as plywood, masonry, hardwood and metals. Other specialty blades are used for dado cuts. Most dado sets have multiple rows of teeth and chippers and they are typically much wider than traditional blades. Be sure that the model of table saw you have can accommodate the type of specialty blades you want to get so you don’t waste your money on a blade that won’t fit.
I got the Hitachi 1 1/2 mouths in the motor died. Says it has a 5 year warranty. I’ve been trying for weeks to get it resolved. Ended up giving up and headed to buy another saw. I understand having products be faulty it’s a numbers game it has to happen to some one. How ever the complete no help to resolve it from Hitachi. Is a problem after a week of back and forth they said they would set up a pick up time to ship and get it repaired over a week still no call back for a pick up. I can’t say enough avoid this headache. I’ve been a contractor for a decade and have had may tools break or need repair. First experience I’ve had that’s made me swear off a brand.hope this will save some one from wasting money and time

The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.
If you are an avid hobbyist, this saw is made just for you. The company is known for its uncompromising quality and durability. This saw has a safety system where the blade stops and retracts automatically when it comes into contact with anything that is not wood.  The microblade guards keep debris from flying all over your workshop. It is easy to change between blades. You will not require a riving knife to do this. Its award-winning dust collection system ensures that you have a clean and presentable workspace at the end of the day.

Accessories 10″ 24-Tooth Carbide Blade, 2x Blade Wrenches, rolling stand, blade guard assembly, push stick, miter gauge, rip fence 10 in. 40-tooth carbide-tipped blade, throat plate insert, smart guard system, rip fence, miter gauge, push stick 32T carbide-tipped blade, rip fence, miter gauge, push stick, and wrenches Rip Fence, Miter Gauge, Smart Guard System, Push Stick, Blade Change Wrenches 24-tooth SKILSAW Carbide-tipped blade for ripping, miter gauge, self-aligning fence, guard system including anti-kick back device, insert plate, push stick and wrench
The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45-degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
Thanks for reading the fine print. About the Wiki: We don't accept sponsorships, free goods, samples, promotional products, or other benefits from any of the product brands featured on this page, except in cases where those brands are manufactured by the retailer to which we are linking. For our full ranking methodology, please read about us, linked below. The Wiki is a participant in associate programs from Amazon, Walmart, Ebay, Target, and others, and may earn advertising fees when you use our links to these websites. These fees will not increase your purchase price, which will be the same as any direct visitor to the merchant’s website. If you believe that your product should be included in this review, you may contact us, but we cannot guarantee a response, even if you send us flowers.
TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.
When considering the type of saw you need for your projects, think about the type of work you want it to do, how much time will be used, the amount of money you want to spend and how much room you will have in your shop for it. If you are only a weekend woodworker and only work an hour or so each time you use it while doing small craft projects the cabinet saw may be a perfect option for you. However, if you own a small woodworking shop and will be working many hours every day with the saw the hybrid would probably be more suited. Before purchasing a saw for your needs, research by reading other consumer table saw reviews to give you the best options.

Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
You cannot build wood cabinets or make furniture without a quality tool that provides maximum accuracy and precision. There are still many people who prefer to use the manual saw rather than the electric saw, but the main disadvantage of using the standard saw is that it doesn’t provide a smooth and clean cut. On the other hand, despite the fact that electric saws cut the wood at a very high speed and reach in the middle of the wood with no effort, they provide a very smooth cut.
My son Owen and I thank you for the truly wonderful, informative and entertaining experience provided by the TOH staff, crew and trades-people at the Pro2Pro Brookline event. From Elizabeth - who welcomed us to the event, to Chris, Kevin and others who were wonderful during the orientation session (answering questions that I'm sure you have heard dozens of times before), to Charlie, Kevin, Richard, Heath (the electrician) and Thomas (the program director), you helped us Insiders to understand and appreciate the pride that you take in your work. It was refreshing. I loved the pictures and accompanying text of the event that you posted. I have to say in closing to Chris, Kevin and Thomas (in particular) you gave my son, a budding landscaper, the impetus to continue his pursuit of the trades. Kudos to you all and keep up your great work!
×