If you’re looking for one of the most powerful products on the market, you’ll find those such options within the 3-5 horsepower range. As you can likely imagine, these are products largely targeted at professionals looking to use their table saw on a day to day basis. If you’re a hobbyist or occasional contractor who doesn’t necessarily want to shell out a fortune on a table saw, you should find that between 1-2 horsepower does the job.

The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
Bigger tables offer more potential for additional extensions. For example, if you’re planning to process a massive piece of wood but you cannot cut it in smaller pieces; a table extension will definitely come in handy. There are a lot of commercial add-ons you can choose from, but you can also construct one yourself if you’re experienced enough. Experimenting with these things never gets old or boring, but keep safety in mind at all times. Make sure it’s completely safe to use the said extension and pay special attention to the amount of vibrations and the overall integrity of the table after you’ve installed the add-on.
The Porter-Cable looks like a beefed-up version of the Craftsman, with the same blade guard and anti-kickback pawls. This is the only saw in our test with a blade-tilting handwheel, which makes it easier to dial in a precise bevel angle. The motor mount and blade controls on this saw are very sturdy, without much play, which translates to a good-quality cut. Extending the fence for a wide rip requires a bit of effort on this saw, since the rails are stiff. All in all, this is a great saw for the price.
The fencing should be perfectly straight and parallel to the blade in order to maintain a safe environment and achieve the best results. As soon as the fencing is taken care of, turn your attention to the blade itself. Is it properly adjusted and sitting at a perfect 90 degree angle? If not, you could encounter some issues while trying to work. You’ll need to find an accurate measuring tool to make sure your table saw blade is resting at a perfect 90 degree angle if you want to see the best results.
On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
In a direct drive, the blade is directly connected to the motor. So the motor can transfer all its power to the blade directly. There is practically no loss of power in this process. It produces much less vibration and noise in comparison to a belt drive. They are relatively small and lightweight. They are also safer! It also costs less so generally it is a winner. However, there are reasons to go for a belt drive for bigger jobs.
If you want to finish your DIY project and you need to a circular saw mounted under a table, the DEWALT DWE7491RS is exactly what you are looking for. With so many models available on the market, more and more people think that buying a circular saw is a piece of cake. However, things are a bit different and choosing the right model for your needs can be an exhausting task. Nowadays, people who are interested in buying such a heavy-duty tool invest in the first one they stumble upon. This is a very big mistake. These tools are so different that you can easily end up with a device that doesn’t fulfill your needs. The DWE7491RS unit measures 24.5 x 31 x 31 in and weighs less than 100 pounds. It is a sturdy unit that features a rolling stand and provides maximum stability. Having a powerful 15-amp motor, this device is great for a plethora of reasons. It can make cuts ranging in depth from 2-1/4 inches at 45 degrees to 3-1/8 inches at 90 degrees. Moreover, it comes with a 1-1/2 inches dust port of the top of the blade and 2-1/2 inches dust port at the back end of the device. Its dual capability helps it capture dust both below and above the blade while leaving your work area clean at all times. After reviewing several models, we can truly say that the DEWALT DWE7491RS is among the highest ranked in the current market. It is a great unit that will surely meet all your requirements.

TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
We spent a lot of time setting up and taking down the saws to see how well the stands worked and how easy it was to install and remove the blade guard and anti-kickback pawls. Then we ran a torturous ripping test with 3-in.-thick slabs of oak to find the best table saw. And finally, we used the saws for more conventional tasks like cutting plywood and ripping framing lumber as another test to determine the best table saw.
I recently brought the Ryobi RTS21G after my dwe745 got stolen and actually couldn’t believe the quality! You guys were definitely right about using the Diablo blade, makes a big difference as it’s not the most powerful table saw in the world, but really didn’t expect much for $200 but i was very surprised. Anyway just wanted to say thanks for the great review and recommendation!
The obvious starting point for an analysis of which saw is best suited to the needs of a given person (or company, school workshop, and so forth) is the budget at hand. Even the most affordable table saws of a quality meriting serious consideration cost more than 200 dollars; such units are small but still capable of many tasks. The top of the line table saws come with price tags topping out at well over 3,000 dollars and can handle almost any lumber you would ever need cut and then some; more often than not these mighty saws are more tool than needed, so to speak.
The best overall performance in our testing was the Skilsaw SPT99-12. The Skilsaw was described by many of the TBB crew as a beast and the data reinforces that. Regardless of the type of material the Skilsaw SPT99-12 offered the lowest drop in RPM’s and the lowest increase in AMP draw. Following in second place is the Hitachi C10RJ and the DEWALT DWE7491RS in third place.

Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.
A table saw is the centerpiece of any home workshop, and it’s often the very first power tool to be cranked up at the start of any woodworking task. They’re essential for the necessary task of sizing wood for each project – whether narrowing the width of boards, cutting plywood sheets, or tackling specialized cuts like grooves, slots, and tenons. Because of their important role in DIY and professional construction, choosing the right table saw is critically important. At BestReviews, we’ve researched table saws in depth. We’re here to help you decide which type of table saw will best meet your needs.
“The SPT99 table saw can accommodate dado cutting up to 13/16″ wide in a single pass. WARNING -To reduce the risk of injury, always disconnect plug from power source before changing blades. WARNING – To reduce the risk of injury, always use the Skilsaw SPTA70WT-DD 1/2 inch Dado Blade Table Insert or the Skilsaw SPT00A 13/16 inch Dado Blade Table Insert (both include dado accessory washer). Never make dado cuts without this insert. Do not use dado sets larger than 8″ diameter.”
This blade shares many features that come standard on other Diablo blades. The carbide teeth are cut from Diablo’s TiCo High Density Carbide. Perma-Shield non-stick coating helps the blade move through material with less friction, reducing heat that can lead to warping in addition to corrosion. Diablo’s Tri-Metal Shock brazing process ensures the teeth stay in place much longer than other blades and can withstand impacts that leave other blades in need of a dentist.
The Bosch GTS1031 Portable Table Saw is an excellent tool for any craftsman - definitely one of the best tools you could add to your work arsenal. We love that it is easily transported from place to place thanks to its lightweight design and ergonomic carry handle. The design transfers all of the weight of the machine to a specified center of gravity and helps to make it easier to carry the 50 pound machine. The Bosch GTS1031 Portable Table Saw also comes with a smart guard system that helps the device perform at peak levels while keep you safe during your work.
Ridgid seems to get mixed reviews from users, maybe due to its lower price point, but continues to impress us in head to head competitions. With this edition, Ridgid’s 15 amp motor powered through cuts better than any other saw we tested. Sure it was close, but it consistently beat out each competitor. That power does come with more vibration than some of the others though.

Great match-up and informative… however I too noticed that “No Load” RPMs varied quite a bit from chart to chart – for the same saw. We would expect some variation of 50 RPM as you had mentioned, but not 500 to 800. See that the Hitachi changed from 4400 down to 3700, Delta jumped from 3700 to 4400, Rigid from 3650 to 4350. Upon closer scrutiny… the order of “No Load” RPMs used in first chart may have been used in all subsequent charts. When the “Load” results were ordered by hi-to-low ranking, is it possible that the “No Load” data was not kept with its saw? If so, that changes the %drop results slightly for most RPM No-Load/Load,Speed charts. No too terrible. Lots of data… Good overall presentation though for use to make informed decisions. Thank you!


One of the first and most important things to consider is what type of table saw you require. When considering the type make sure you consider things like, where will be using the saw, will it need to be portable and move from job to job or can it be stationary like in a work shop. Also, what will be the largest size bits of timber I will be cutting, what sort of power will I require and budget, below we’ve listed the main types so we hope it helps you find the right type for you.
When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.

However, some models with cheaper table surfaces still manage to get it consistently right. It’s always important to look for problems with table flatness when reading reviews of table saws you’re considering. If you see flatness as an issue repeatedly, you can save yourself a huge potential headache by just considering a different model. If you don’t see any complaints about table flatness, even on a cheaper model of table saw, then it’s probably going to work out just fine.
When using the side extension, a tape moves along so you won’t have to remember what measurement to lock the fence on or read a double marked measurement guide. It’s an innovation we like, but there are questions as to the long term durability of the tape itself. Like Ryobi, Ridgid uses a magnetic throat plate to secure it while leaving access simple.
Just in time!!! My Sears Craftsmen portable saw died on me last week. It was only 12 years old with minimal use. It was a nice saw with a nice sized table, not heavy, and a stand that separated and folded like an accordion. Unfortunately, as it turned out, the gear teeth on the worm drive had worn down to the point where the saw started slip and whine. Now that Sears is defunct (Canada), I have no other option than to replace it due to no parts being available.
Portable table saws are made to easily transport, making them a perfect utility saw for carpenters. Portable saws function exactly the way a big table saw works. The difference is the portable table saw does not have the huge motor as the types of saws. Because they use the smaller motor, they are not as powerful and are also loud. They are less durable and are not as stable as the larger saws. One good suggestion for a portable table saw is the Ryobi Table Saw.
When using the side extension, a tape moves along so you won’t have to remember what measurement to lock the fence on or read a double marked measurement guide. It’s an innovation we like, but there are questions as to the long term durability of the tape itself. Like Ryobi, Ridgid uses a magnetic throat plate to secure it while leaving access simple.
For centuries, the job of the sawyer was, quite simply, to saw logs into lumber. Working in two-man teams, a pair of sawyers would use massive saws -- called whipsaws or pitsaws -- to cut felled trees into workable planks with their own muscles as the motive power. The job was exhausting and often dangerous, yet necessary to create the precious lumber used to build everything from homes to railroad bridges.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.
The Delta 3 HP Motor 10 in. UNISAW with 52 in. BIESEMEYER Fence System gets its name from the fact that the manufacturer claims you can use this saw to replace all the others that you might use. It comes with a 52-inch fence system that attaches right to the top of the table holding boards and front cranking handwheels that let you extend the opening of the blade. Delta claims that this cabinet saw has the largest opening of all currently available models.
This type requires a heavy-duty circuit because it’s driven by a powerful 3 to 5HP motor. The blade is driven by three parallel V-belts which ensure a smooth operation and an efficient transfer of energy. Needless to say, if you have big plans, you might want to consider investing in a high-quality cabinet saw. Prompted, it’s going to cost you a significant amount of money, but it pays out relatively quickly.
According to the many reviews posted online, the JET 708675PK is an excellent table saw that features a finely ground and large cast iron table that measures twenty nine by forty two inches and provides plenty of work surface for even the most demanding projects. Also, taking a closer look at the front of the blade, you’ll notice it includes ten inches of clear table which is certainly going to be appreciated by a lot of users. Looking under the table, you’ll notice a wide stance, heavy duty cast iron trunnion mechanism which provides the remarkable performance, almost vibration free operation and incredible stability the JET 708675PK is known for.
Though you’ll still want to wear safety gear when using this table saw, it has safety features that will keep you safe too. One of those features is an emergency stop. One touch of the bright green power button brings the motor to life, but when you lift up on the emergency stop that surrounds the power button, you can stop the motor in its tracks. This button has a convenient design that lets you hit and lift it with your leg or knee too.
The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45-degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.
Bengt – We appreciate the feedback as it always helps us get better. Having said that I think some of your concerns were evaluated and included in the results in ways that may not be entirely clear. We adjusted each saw after checking the blade/fence measurements and had no issues getting them adjusted (I may add some text to reinforce that in the article). We don’t do long term testing in this type of article as it’s simply not feasible…so making a statement about whether the saw holds those adjustments isn’t feasible. We evaluated the fences and ranked them in the ergonomics section, we even did lateral load testing on them as part of that ranking.

The cabinet saw available on the market today is the SawStop ICS51230-52 5 HP 230V 60 Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System, which comes with the longest fence system that you’ll find. Not only is that system easy to use, but it allows you to make different types of cuts and change the orientation or angle of the wood to the blade.
SawStop has an excellent stand and they’ve cleverly hidden the tool/miter/riving knife storage box under the side extension. Move the table extension and the box presents itself. Like DeWalt, two riving knives come with the saw—one with safety guards and one without. This keeps you from wondering how the pawls and guard go on the riving knife. Blade height fully adjusts with only one turn of the wheel. Not everyone was on board with this, citing less accuracy for dado and rabbet cuts. In the end, we showed we could be as accurate on the height as any of the other saws, so it’s a win.

Our table saw review quickly showed that today’s portable table saws are light-years ahead of the small-saw offerings from a decade ago. They feature big-capacity cutting, greatly improved safety features and attached stands for easy setup. And saws in the upper price range rival stationary saws in accuracy and quality of cut. We limited our review to saws that included a stand with wheels and ones that could rip at least 24 in. wide, only the best table saw for our readers!
×