And finally, there are a couple of jobsite table saws running around with flesh detection to drop the blade out of the way if it detects a strike. There’s a significant premium in cost for these saws and there has also been plenty of litigation regarding whether it should be required on every table saw and whether more than one company has the right to manufacturer the mechanism. But they’ll save you a much worse injury in the event of an accident.
We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.
This next factor to take into consideration when it comes to buying a table saw is more of a safety feature but one that you’ll want to look for in every table saw. It’s basically an automatic switch that turns of the table saw when you walk away. It’s often the case with some cheaper table saws that when you’ve finished using the table saw and forget to flick the power switch, the unit will remain on. This leaves anyone who goes near the table saw open to a considerable amount of danger.
No doubts about it, a table saw is one of the most important tools a woodworker can have in its garage. There are dozens of models on the market and after reviewing a lot of them we can say that it is more than complicated to take the right decision. Therefore, if you are looking at buying a quality machine, but you have no idea about their features, construction, design and so on, below is a comparison table specially made for people like you. In this comparison chart, you will find detailed information about the best models in 2018.

The purchase of a table saw is no doubt a big investment. But there is a lot of flexibility in this class of tools to find one that fits in with your budget and your wants. Make sure to take into account how you will need to use the tool and where you will need to use it. Heavier models will be sturdier but they will also require more effort to load up when you need to.
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.

The fencing should be perfectly straight and parallel to the blade in order to maintain a safe environment and achieve the best results. As soon as the fencing is taken care of, turn your attention to the blade itself. Is it properly adjusted and sitting at a perfect 90 degree angle? If not, you could encounter some issues while trying to work. You’ll need to find an accurate measuring tool to make sure your table saw blade is resting at a perfect 90 degree angle if you want to see the best results.

Portable table saws are made to easily transport, making them a perfect utility saw for carpenters. Portable saws function exactly the way a big table saw works. The difference is the portable table saw does not have the huge motor as the types of saws. Because they use the smaller motor, they are not as powerful and are also loud. They are less durable and are not as stable as the larger saws. One good suggestion for a portable table saw is the Ryobi Table Saw.
Ridgid notches a third place finish as the only saw to include an independent blade height lock. The adjustment wheel raises and lowers with multiple full turns like most saws, but integrates a lock into the center. For the bevel adjustment, the outside of the height adjustment wheel turns a rack and pinion style system to accurately change the blade angle – a feature Makita shares.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
Great job with this testing. As far as the Hitachi. Many sources online point to minimal startups of the Hitachi c10rj before becoming unusable (not starting). The soft start module apparently doesn’t hold up. If it happens in 30 days it can go back to the store but after 30 days you call Hitachi (most described as unpleasant) drive to your closet Hitachi Service center and wait (up to months). I really like the Hitachi myself but am afraid of the soft start module error. THANKS FOR ALL THE GREAT WORK AND CONTENT. Please forgive any punctuation etc. This is tough on phone.
The table measures up at 29 inches by 21.5 inches. The 4100-09 is not suitable for dealing with large stock or sheets of wood. Made from aluminum, you’ll meet with no resistance as you slide the timber toward the blade. The only negative with the table is the way it’s finished with an anodized coating. This is fine to start with but tends to wear over time, something that doesn’t just look unsightly but can ultimately affect accuracy. This is a surprising oversight from Bosch and one we hope they rectify in future iterations of this fine table saw.
Bosch’s Gravity Rise Stand was the best portable design of the group. While several stands share the basic principles, Bosch stood out with large diameter tubing that improves durability, the ease of set up/take down, and the larger pneumatic wheels that helps over less than ideal terrain. SawStop was right behind with slightly narrower wheels while Ridgid wrapped up the top 3 most impressive.
A cabinet table saw is so named because it has an enclosed style base. This saw is the opposite of the contractor saw. Cabinet table saws are designed to be functional and lasting to meet the qualifications that are required by people who work with wood for a living. They are constructed to be more durable than contractor saws. Makita table saw offers many popular options at a very affordable price.
1. Is it possible that the SkilSaw SPT99-11 and SPT99-12 have the ability to accept up to a 13/16″ dado set instead of just the 1/2″ max your review states? I have seen the larger spec stated elsewhere. If not, why? Is the arbor just not long enough? Or is it a zero clearance plate problem? I can’t imagine having to do two passes to complete a 3/4″ dado. The 1/2″ max seems a weird anomaly as compared to all other saws in the class.
But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.
All of these great features, combined with the cast iron table top make this saw a tool to be reckoned with. The  SKIL 3410-02 10 Inch Table Saw has a 32 inch rip capacity. You’ll be able to easily and efficiently make cuts by implementing their EZ measurement system. All you have to do is line up your wood and focus on doing the work you love. It’s easily transportable, easily adjustable, and easy on your bank account - and really, what more can you ask for in a tool?

My son Owen and I thank you for the truly wonderful, informative and entertaining experience provided by the TOH staff, crew and trades-people at the Pro2Pro Brookline event. From Elizabeth - who welcomed us to the event, to Chris, Kevin and others who were wonderful during the orientation session (answering questions that I'm sure you have heard dozens of times before), to Charlie, Kevin, Richard, Heath (the electrician) and Thomas (the program director), you helped us Insiders to understand and appreciate the pride that you take in your work. It was refreshing. I loved the pictures and accompanying text of the event that you posted. I have to say in closing to Chris, Kevin and Thomas (in particular) you gave my son, a budding landscaper, the impetus to continue his pursuit of the trades. Kudos to you all and keep up your great work!
×