One of the first and most important things to consider is what type of table saw you require. When considering the type make sure you consider things like, where will be using the saw, will it need to be portable and move from job to job or can it be stationary like in a work shop. Also, what will be the largest size bits of timber I will be cutting, what sort of power will I require and budget, below we’ve listed the main types so we hope it helps you find the right type for you.

Ridgid notches a third place finish as the only saw to include an independent blade height lock. The adjustment wheel raises and lowers with multiple full turns like most saws, but integrates a lock into the center. For the bevel adjustment, the outside of the height adjustment wheel turns a rack and pinion style system to accurately change the blade angle – a feature Makita shares.


In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
The Delta 36-L552 is the right cabinet table saw for boat building cabinet making and also woodworking. It features a fifty two inch Biesemeyere fence, speedometer style scales and also dual crank (up-front) controls with locking cams. Taking a closer look at the inside of the Delta 36-L552, we find a powerful 5 HP motor rated at 220V which is perfect for cutting engineered products such as melamine, MDF, but also hardwoods.

If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.
Powermatic is a name that you’ll see a few times on our list of the cabinet saws because this company is responsible so many great models like this 1792010K PM2000, 5HP 1PH Table Saw, with 50-Inch Accu-Fence System. The built-in caster system makes it easy to move the cabinet saw anywhere around your shop with minimal eft, and it comes with a quick release riving knife that reduces vibrations to prevent accidents. At 39-inches high, it also lets you use the saw without stopping over.
Still featuring the T-Glide Fence System for smooth, safe operation without compromising on precision measurements and secure locking for repeatable cutting, the TGP236 is still an exceptional cabinet saw in its own right Furthermore, the blade height and angle are still fully adjustable via the comfortably large hand wheels on the front and side of the cabinet itself.
I recently brought the Ryobi RTS21G after my dwe745 got stolen and actually couldn’t believe the quality! You guys were definitely right about using the Diablo blade, makes a big difference as it’s not the most powerful table saw in the world, but really didn’t expect much for $200 but i was very surprised. Anyway just wanted to say thanks for the great review and recommendation!
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.

I have many bundles of old barn boards for sale. These boards are close to 100 years old if not older and they have all had the square and round nails removed from them. This lumber is completely dry and I am selling them in different sized bundles for those who need different amounts of lumber. The old circle saw marks are clearly visible on each board as seen in the pics. Many people use old ...
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.

When using the side extension, a tape moves along so you won’t have to remember what measurement to lock the fence on or read a double marked measurement guide. It’s an innovation we like, but there are questions as to the long term durability of the tape itself. Like Ryobi, Ridgid uses a magnetic throat plate to secure it while leaving access simple.
The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.
The power transfer system is neatly done. The model features a serpentine belt which is quiet and smooth during operation. Therefore, the level of noise is satisfactory. Precision is something that makes this model worth checking out. Whether you’re a professional or a beginner, you’ll definitely appreciate the accuracy of this model. On the other hand, with great things come great responsibilities. Don’t forget to wear safety equipment!
One thing manufactures noticed over the years was that when people used the splitters in normal straight cuts it worked well but it’s biggest downfall came when contractors wanted to do cross cuts. What would happen is that people would remove the splitters to make the cross cuts but then forget to fixed them back in place. One brilliant table saw safety feature is the riving knife. The Riving knife is attached directly to the blade mechanism, this allows it to always be attached not matter where or what angle the blade is.
Though this Jet 708674PK XACTASAW Deluxe 3HP Cabinet Saw comes with the same three-horsepower motor found on the last cabinet saw, it comes with a shorter 30-inch rip fence that may be a little too short some of your projects. It features all the same great features that made Jet so popular with contractors, including a cast-iron enclosed cabinet that stops dust from entering the motor and a poly-v drive belt system that runs more quietly than other belt systems.
When considering the type of saw you need for your projects, think about the type of work you want it to do, how much time will be used, the amount of money you want to spend and how much room you will have in your shop for it. If you are only a weekend woodworker and only work an hour or so each time you use it while doing small craft projects the cabinet saw may be a perfect option for you. However, if you own a small woodworking shop and will be working many hours every day with the saw the hybrid would probably be more suited. Before purchasing a saw for your needs, research by reading other consumer table saw reviews to give you the best options.
Higher-End Models: The higher-end table saws ranged in price but were somewher between $ 500 - $800. These had a built-in "stand system", the largest table dimensions and the largest ripping capacities (both to the left and right side of the blade). The features were similar to the lower priced models though, so you are not paying for features, from what I've noticed.
Patrick – Thanks for the feedback. Trust me, I wish we could spend more time on every aspect but we spent hundreds of hours as it was. I can tell you that the rack and pinion fences are much better than the standard fences of the past. Our entire group felt strongly that we’d prefer the rack and pinion on all the saws. We felt the Ridgid and Delta fences were the least impressive of the standard type.

Today's table saws also include riving knives, which ride up and down with the blade when its height is changed, rather than splitters that are fixed in place. The problem with the old splitters was that they had to be removed for certain types of cuts, and users might forget to put them back on before making rip cuts. This increased the risk of kickback injuries, which occur when the spinning blade kicks back a piece of wood toward the user with tremendous force, causing serious injury to any part of the body that's hit.
The only flaw might be the occasional false detection by the safety system. This will usually only happen if the lumber is wet or it is used primarily in the outdoors. You have to weigh the safety features against the type of work you do. If you are constantly working in wet or damp environments, it might not be worth the headache. If not, it’s 100% worth the benefits!
The market for table saws is one that’s incredibly varied and that’s something that you’ve likely already noticed from just one look at the different table saw types. Reading on into our table saw reviews and you’ll notice that there’s also a range of different brands offering table saw products. But which brand is best for you? With so many of them available, it’s hard to understand the difference and make a choice over the best brand for you.
However, thanks to the innovative safety technology incorporated into the design, you’ll never have to worry about incurring severe injury. The tool is capable of sensing human touch and will shut down within milliseconds of accidental contact. You’ll be able to work in a safe and clean space with no worries if you invest in the best quality tool like the SawStop table saw.
The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.

These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.
One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.
SawStop was second, also with features no other saw had. The blade height adjustment wheel covers the entire range with one full turn of the wheel. There was some discussion about micro adjustments being more precise for dado and rabbet cuts, but in practice, we found we could easily get to a specific height without trouble. SawStop also moves away from the bevel lock lever and instead integrates it into the height wheel. By pulling the lock toward you, it is released and easily moved to your desired angle. Let go of the wheel and it’s locked back in place without having to hold it and use a second hand to work the lever.
Another important element of every model is the fence. Without the fence, you cannot make a precise cut. The most common type of fence that you can find on these units is the T-square fence. However, before getting into that let’s go over the most important characteristics a quality fence must have. First of all, it is important to know the role of the fence. It allows for hassle-free adjustment both vertically and horizontally. Also, it must be placed on the rails firmly, so you don’t encounter resistance while moving it. However, if this happens you can apply wax. Now, let’s have a look at the T-square fence. It is so popular because it is easy to adjust and maneuver. More than that, it is extremely accurate.
Below we’ve included the current pricing (at the time of publishing this article). Pricing includes the cost of the stand and ranges from a low of $349 for the Hitachi to a high of $1,299 for the SawStop. The lowest price isn’t always the best in our opinion, we’re looking for the best value.  The Hitachi is an incredible deal at $349 and our top pick for price and value for a saw that has lots of power, a rack & pinion fence, and a solid stand.
As you’ll be able to tell from our table saw reviews, the different types of table saw are largely targeted at different types of users. If you’re likely going to need to transport your table saw around from site to site, it’s a portable table saw that you’re going to want to opt for. It’s pretty clear that the portable variation of table saw is designed with maneuverability in mind, meaning you can just pack it up with your kit and leave.

The Shop Fox W1819 also comes with a miter fence with flip stop which provides excellent workpiece support and is great for longer workpieces. As for the flip stop, it’s going to be very useful especially when wanting to make several cuts of the same width. If you want to cut longer workpieces, you can also flip it out of the way and then pivot it back down in order to make more cuts at the cutting width of your choice.
Another indication of how hard a table saw is working is monitoring the amperage (AMP) draw under loading conditions. We measured the amp draw for each saw using all three materials again at the same time we were recording RPMs. The first graph below shows the amp draw for each saw cutting plywood compared to the no-load amp draw. The white bar on the left indicates the no load amps and the colored bar on the right shows the maximum amp draw during the cut.

When it comes to the type of wood that you can cut through with a cabinet table saw, you can purchase one in confidence of the fact that you’ll be able to cut just about any type of wood. That being said, as a general rule, you’ll find that the more expensive cabinet table saws offer great strength and flexibility. However, in terms of the pricing of table saws, you’ll definitely find that they can become pretty expensive. This is no surprise though really, especially when you take into consideration the fact that cabinet table saws are designed solely to be used within a professional environment.

It is safe to say that we live in a DIY era. Think about it. When was the last time you went on YouTube or anywhere else online and looked for something that tickled your fancy, a guide on how something is made or done, or maybe a tutorial. Indeed, we do it very often, so why should woodworking and home improvement be any different? With the prices of table saws constantly dipping and the insane number of choices on the market, you can get one for yourself and save thousands of dollars by doing things yourself instead of hiring contractors.

×